Today, more than ever, simplicity of cutting clothes is in trend. The loose dress has been a hit for several seasons in a row. Only the density of the material, the decor change, and some modeling moments are introduced, but basically the cut remains unchanged. The pattern of a free dress is quite simple to build, so even the most inexperienced seamstress will cope with sewing such a product. Of course, you can easily go to the store and buy the finished product. But independent tailoring has a lot of advantages, the main of which is the cost, which allows you to treat yourself to a couple of new things for the same money. How to sew a loose dress at home, and will be discussed further.

Material selection

A loose dress is best sewn from knitted fabric. It should be chosen based on the time of year. For winter, you can take angora or wool, for spring and autumn - diving, footer, jersey, for summer, stretch cooler and micro-oil will be ideal. Also in the work you can use dress fabrics with a transverse stretch. The advantage of stretch fabrics is that they wrinkle less. And given that the free dress is wide enough, this fact plays in favor appearance things.

Sewing preparation

Calculations and taking measurements are an integral part of the process of creating blanks for any product. The free dress pattern is based on the following body measurements:

• bust, waist and hips;
• chest height;
• back and shoulder width;
• back and front height to the waist;
• length of the product;
• girth of the upper arm;
• neck circumference.

All measurements should be recorded on a piece of paper to make it easier to transfer them to the drawing.

Creating a pattern

A loose dress, as a rule, has either a trapezoid shape or a straight silhouette. The template for both models is the same, and all additional elements are built during the modeling process. The template is best done on a piece of wallpaper or construction film. The latter option is more practical if you plan to create not one, but several dresses.

So, in order to sew a free one, you will first need to develop a pattern based on measurements taken. First, you should draw a rectangle in which half of the back and half of the front will be built. The upper and lower sides should be equal to half the girth of the chest, and the sides - the length of the product. From the upper corner, you need to step back by the size of the measurements “chest height” and “back and front height to the waist” and draw additional horizontal lines. The first will be the chest line, and the second will be the waist line. From the latter, you should retreat another 20 cm and mark the line of the hips. Continuing to create the basic grid, you should note the width of the back and calculate the width of the armhole in order to draw additional verticals. To do this, along the chest line from the left side of the rectangle, the value of the measurement “back width” recede and put a point from which the armhole begins. To calculate its length, you need to divide half of the chest volume by 4 and add 2 cm. This value is also marked on the chest line and put a dot. The rest will refer to the front shelf.

Next, proceed to the designation of the shoulder seams and neck. Everything is quite simple here: the value corresponding to half the girth of the neck recedes from the upper corners and the shoulder area is highlighted. In this case, the extreme point should be underestimated by 1 cm, and from the side of the back, the rounding of the neck should be raised by 1 cm, and the shoulder seam should also be drawn with a bevel of 1 cm. point, connecting it with the edges of the shoulder seams. From this central point lower down side seams, which are somewhat bred to the sides to the bottom line, in accordance with the volume of the hips.

The loose dress eliminates waist darts, which simplifies the construction of the template. However, if the fit is not satisfactory, the product can be fitted a little from the back.

Sleeve construction

For a free cut, it will be enough to process the armhole. A warmer version will need to be supplemented with a sleeve. It can be one-piece or set-in. They are being built different ways. If you continue the shoulder seam and, cutting the details of the base of the dress along the side seam, remove the lower cut of the sleeve from it, a one-piece version will come out. For a set-in sleeve, you will need to fold the details of the base along the shoulders and transfer the cut of the armhole to a separate sheet for the drawing. After that, along the upper rounding, you will need to rise by 1.5 cm and draw a circle based on the outline of the resulting line. On the lower border of this figure, in the center, you should place a measurement of the girth of the upper part of the arm and draw an eye, descending along the borders of the circle and reduced to a straight line.

decorative elements

The dress will come out truly sophisticated if you use the decor correctly. For example, plain knitwear can be diluted with lace inserted into the shoulders or around the neck. You can also beat a contrasting combination of canvases of the same quality. Loose dresses, the photos of which are presented in the article, have various decorative embellishments that can serve as an example or become more interesting ideas design.

In addition to the standard decoration options, you can experiment with textures. For example, make a dress with a light chiffon collar and sleeves with mother-of-pearl buttons. In combination with dark knitwear, this dress will be a great office option.

Do not forget about such elements as pockets, they will perfectly complement loose dresses. Photos of finished products on models will allow you to determine the most appropriate location of these elements. Welted, overhead and with a leaflet, decorated with rag roses, rhinestones and sewn-on stones on a strict silhouette of a wide cut, they will look very harmonious and make the image interesting and stylish.

Assembly of parts

In order for the product to come out of high quality, you need to sew all its elements in correct sequence. First of all, work is carried out with the front shelf, in particular, pockets and other model elements are made out. Next comes the turn of the shoulder seams and stitching of the sleeves. After close side cuts and sewn to the neckline. Next comes the turn of processing the bottom of the sleeves and hem.

fashion designer

Hello dear readers!

The purpose of our lesson is to learn how to model dresses based on basic pattern. The kind that beginners can handle. In addition, we will analyze simple styles of dresses that suit the type of your figure, using the example of which you can, if you want, create more complex models, enriching them with details and using a combination of textures of fabrics and colors.

We are sometimes written: "It is very difficult for me to buy ready-made clothes, my figure is an inverted triangle, besides, I have a very decent bust and a wide rib cage, that is, my chest volume is 102 cm - this is a very big disappointment for me. I don’t have the opportunity to buy any thing for myself, because the rest of the parameters of the figure go to 44-46 size ... What style can I choose?

Of course, having parameters that do not fit into the standards, it is difficult to find something in the store to your liking, and sometimes a trip for new thing turns into a mess. Well, well, you should not be sad, especially for a person who has at least a little experience in tailoring. And with patterns, simple ones that even a novice tailor can create, we will try to help. It's no secret that all dresses in the world are sewn using one universal pattern, modifying and modeling it. Having such an invaluable tool in your arsenal, the creation of which on our website will not take much time, you will be able to dress according to your taste and image invented by you.

First, what is a basic pattern? This is a pattern without model features, roughly speaking, this is a human figure made in a two-dimensional plane. The pattern has a different degree of fit, depending on what type of clothing will be designed in the future - upper (coat, jacket) or light (dress, blouse, corset, etc.), and differs in the amount of freedom. Therefore, on our website you will find and, as well as, they will differ in increases, which is very important. By the way, on our site, along with the ability to build a basic pattern according to individual sizes, there are already a number of models of dresses that are absolutely excellent in cut and suitable for women different types of figures. You can also use them, especially since each size is presented in three heights, and this is very important for a good fit of the finished product.

So, having a basic pattern on hand, we can proceed directly to modeling. First, let's choose a dress model. This item must be taken very responsibly, objectively assessing your appearance, figure, image as a whole. After all, it is no secret that we are all different people, each of us has our own individual figure, sometimes not fitting into the so-called "ideal framework", especially since this very ideal is different in every time period, it is changeable according to fashion trends. We will not adjust ourselves to the standards and love our individuality. All female figures are conditionally divided into several body types, and each of us belongs to one or another type to a greater or lesser extent.

Illustration from https://high-fashion21.ru

Modeling a dress for the type of figure "Triangle" (pear)

A pear-shaped figure is very feminine, but sometimes it brings some difficulties to the owner when choosing a finished dress due to the difference in the girths of the hips and chest. You shouldn't get upset. First, let's figure out which style to choose. We narrow the bottom and focus on the upper part: a boat-shaped neckline, a large collar, a neckline, a bright print in the upper part of the dress, the bottom can be slightly flared, do not forget about the use of contrasting inserts that run along the dress and visually model the figure, as well as a little high waist, heels and matching tights will make you slimmer. We try to avoid decor in the hips, patch pockets, draperies, transverse stripes and large prints.

For an example of modeling, we will choose a simple sheath dress created on. The style is interesting in that the model lines that form the silhouette demonstrate the best and most advantageous female figure just the lower type. Dark inserts running along the side seams will help to visually hide the width of the hips, and the white silhouette, expanding upwards, will bring to the fore the built silhouette. But, here you can’t be too smart with excessive narrowing of the skirt, and if the difference between the girths of the chest and hips is large, it is better to expand the skirt a little to the bottom.

Modeling. On the details of the back and front pattern, draw model lines of reliefs passing from the armholes to the bottom of the dress through waist darts, on the back, transfer part of the solution to middle line backrest, for the greatest fit in this area. Open the chest dart in the armhole, read more about transferring darts here. It remains only to outline the allowance for the slot. If the difference between the circumferences of the waist and hips is large and the solutions of the tucks for fitting are more than 3-3.5 cm each, the tuck must be divided into two, otherwise finished product there will be ugly creases in the waist area.

In the second version of modeling, we offer to expand the skirt to the bottom, make it the so-called A-line, you can also make the dress cut off at the waist.

Modeling a dress for the type of figure "Inverted Triangle"

Your strong point is narrow hips and long slender legs. We focus on them. The whole decor, bright prints - down on the skirt. We reduce the width of the shoulders, raglan sleeves will help us here, or the absence of sleeves at all in summer clothes, a dress with a shoulder strap on one shoulder, a Greek silhouette, a loose tunic, a dress with a tulip skirt can become a lifesaver and be loved in your wardrobe. You can afford to wear curvy wide skirts, skirts or trousers with a peplum, dresses of a straight cut, but not too voluminous and wide, with vertical seams or trim.

As an example, let's analyze the modeling of a pattern simple dress suitable for this body type. It features a fitted, sleeveless bodice and a tulip skirt that adds volume to the hips. The dress is cut off along the waist line, on the front panel of the skirt there are two opposite folds, on the back panel of the skirt a cut is made.

Let's start modeling by applying to the details of the back and shelves embossed lines (if you want a better fit or the fabric is knitted, you can use the base pattern of the adjacent silhouette). Thallium tucks on the front panel of the skirt will be folded - cut the skirt part from the end of the tucks vertically down, push the parts apart so that in the upper part we get a gap of approximately 6-8 cm to form deep counter folds. At the bottom, the volume of the skirt will be kept in its original form.

Modeling dresses for the type of figure "Hourglass"

The type of figure "hourglass" is the most feminine, it is he who is rightfully considered the standard to follow and we try to bring our figure closer to it, at least with the help of clothes. Lucky women with this type of physique. Main advice- focus on the waist, so you will further emphasize your femininity and sexuality. Necklines, bows, pencil skirts, stilettos - this is your win-win look.

Let's model such a simple dress, in two versions.

The model is quite simple at first glance, but with the right choice of fabric and accessories, it is very effective.For modeling we need and . The dress is detachable along the waist line, the skirt is expanded to the bottom. Darts for fitting the chest are transferred to the neck: in the first version - darts from the neck are stitched with an allowance outward, a small sleeve with a fold, in the second version - darts on the chest are distributed into folds coming from the neck, there are no sleeves.

Modeling. Step 1 - on the details of the back, the tuck for the roundness of the shoulder can be neglected, because. the neckline of the back is deep enough and widened, but the amount of the opening must be taken from the length of the shoulder so as not to disturb the balance. For the convenience of modeling, we will translate the tuck on the shelf into an armhole. Cut the details of the skirt pattern lengthwise from the darts down.

Next, step 2 of the simulation. Let's outline a new neckline according to the sketch. We will transfer the thallium tuck on the shelf to the neck, and we will also transfer the tuck from the armhole there. Read more about the translation of tucks. When designing a detachable adjacent silhouette, the pattern of the shelf detail must be lowered by 1 cm in the waist area, this will give a better fit and prevent it from pulling up when finished. Skirt. We connect the parts of the pattern, obtained after cutting the details of the skirt, so that the darts open to the bottom. We will correct the side sections and the bottom of the product.

Sleeve modeling. You can take a pattern for the base of the sleeve on ours. First, shorten the length to the required. With the help of vertical cuts going from the edge to the bottom of the part, and the subsequent separation of the parts of the pattern, design an oncoming fold.

More sleeve modeling can be found in this

In the second version of the dress, the tucks on the shelf are translated into folds coming from the neck. Modeling will be discussed below.

Modeling a dress for the type of figure "Oval" (apple)

Oval shape (apple). In the era of Rubens, women with this type of figure were the ideal of perfection. The silhouette is visually close in shape to the letter "o". The strategy in choosing the right clothes will be to emphasize, accentuate the waist, this can be done by choosing a dress that expands slightly towards the bottom, as well as using belts, decorative inserts that make the waist visually narrower, the top of the dress should be slightly expanded, for example, use a V-shaped neckline, collars . Sheath dresses, wraps, low waist, dresses A-line silhouette suit you.

Let's take this dress as an example. It is interesting because it has a contrasting decorative line running along the dress. Visually, this very stretches the silhouette and slims. In addition, the dress is loose at the waist and slightly expands towards the bottom, which is undoubtedly a plus for this type of figure. Clear cut lines and a choice of fabric that holds its shape create the right image and collect the figure as a whole. To simulate this model, we will use , for a better fit.

Modeling. The side cuts of the parts are straight, because The dress has a straight loose silhouette. We will transfer the tuck on the bulge of the chest to the side seam and outline the relief line. Shorten the pattern of the sleeve detail just above the elbow.

In the details obtained, we outline the front yoke and cut it off.

Modeling a dress for the type of figure "Rectangle"

Rectangle female figure. For modern models is the most typical. Therefore, when buying ready-made clothes, there are usually no problems, but sometimes you really want something special! That's where our modeling tips and patterns can come in handy!)) Women with this body type do not need to try to look like Marilyn Monroe or Sophia Loren, this is not your style. Dresses and clothes in the image of Twiggy, Kate Moss, Nicole Kidman and Coco Chanel herself, that's what we are striving for.

We chose the right dress for the modeling lesson. We need a pattern this time. Sleeveless dress, free-cut with an opposite pleat going down from the neck, fastened at the bottom to give the product an oval silhouette. Pockets can be made in the side seams.

It is the dress that can make you more feminine and beautiful, convey your romantic or sensual mood, emphasize the dignity of your figure and hide flaws, visually make the figure more slender. A dress can save in a situation where there is no time to match a blouse with a skirt or trousers, a jacket, etc. Due to the variety of styles with the help of a dress, you can create a variety of images: from business to sexy. The main thing is to choose the right style of dress for your figure.

MODELING OF A DRESS FOR A TRIANGLE (PEAR) BODY TYPE

A pear-shaped figure is very feminine, but sometimes it brings some difficulties to the owner when choosing a finished dress due to the difference in the girths of the hips and chest. You shouldn't get upset. First, let's figure out which style to choose. We narrow the bottom and focus on the upper part: a boat-shaped neckline, a large collar, a neckline, a bright print in the upper part of the dress, the bottom can be slightly flared, do not forget about the use of contrasting inserts that run along the dress and visually model the figure, as well as a little high waist, heels and matching tights will make you slimmer. We try to avoid decor in the hips, patch pockets, draperies, transverse stripes and large prints.

For an example of modeling, we will choose a simple sheath dress created on a pattern-based adjoining silhouette. The style is interesting in that the model lines that form the silhouette demonstrate the female figure of just the lower type in the best and most advantageous way. Dark inserts running along the side seams will help to visually hide the width of the hips, and the white silhouette, expanding upwards, will bring to the fore the built silhouette. But, here you can’t be too smart with excessive narrowing of the skirt, and if the difference between the girths of the chest and hips is large, it is better to expand the skirt a little to the bottom.

Modeling. On the details of the back and front pattern, draw model lines of reliefs passing from the armholes to the bottom of the dress through the waist darts, on the back, transfer part of the solution to the middle line of the back, for the greatest fit in this area. Open the chest tuck in the armhole. It remains only to outline the allowance for the slot. If the difference between the circumferences of the waist and hips is large and the solutions of the tucks for fitting are more than 3-3.5 cm each, the tuck must be divided into two, otherwise ugly creases in the waist area will appear in the finished product.

In the second version of modeling, we propose to expand the skirt to the bottom, make it the so-called A-shaped silhouette, you can also make the dress cut off at the waist.

Modeling a dress for the type of figure "Inverted Triangle"

Your strong point is narrow hips and long slender legs. We focus on them. The whole decor, bright prints - down on the skirt. We reduce the width of the shoulders, raglan sleeves will help us here, or the absence of sleeves at all in summer clothes, a dress with a shoulder strap on one shoulder, a Greek silhouette, a loose tunic, a dress with a tulip skirt can become a lifesaver and be loved in your wardrobe. You can afford to wear puffy wide skirts, peplum skirts or trousers, straight-cut dresses, but not too voluminous and wide, with vertical seams or trim.

Everyone prepares for it in their own way, but, of course, in advance: children write letters to Santa Claus, ordering the desired gifts, grandmothers make lists of dishes, from the mere sight of which guests and relatives will gasp in surprise, men puzzle over what gift to put under the Christmas tree of an incomparable mother-in-law, well, real fashionistas should take care of the dress in which you will see off the eventful 2011 and meet the new happy 2012! I will try to help you right choice and look fashionable, stylish and comfortable at the same time.

Probably ... this is the most beautiful of all the posts that I did! Its compilation gave me just a lot of pleasure! I hope that when viewing this post, a festive, joyful, light mood will be transferred to you! So, enjoy, choose and start immediately!

MODELING OPTIONS!!!

Modeling according to the options listed below is necessary according to the pattern-basis of the dress, made according to your own measurements.

OPTION 1
This chic dress was created for real beauties! And that is why such a dress should be in your wardrobe for the occasion of the “Big Out”! And sewing this dress is not as difficult as it might seem at first glance. Feel free to get down to business and surprise everyone with a chic outfit.

Pattern modeling.

Since this dress is very tight-fitting, take the minimum amount of freedom to fit.

On the front half of the dress on the skirt, flare as shown in the dress pattern1. The more you give into the flare, the more fluffy skirt will be down.
Draw on the template the cutout of the front half of the dress and the armholes of the dress. Cut piece 2. Cut the top of the front half of the dress along the lines and move apart as shown in pattern 2. If you want more gathers, move the pieces 3 cm apart instead of 2.
Model the back of the dress in a similar way.
Additionally, you need to cut out a part for draping the dress at the waist: for part 2, cut out a rectangle. The width of the rectangle should be equal to the width of part 2, and the height should be 2 times wider.
The rectangular part must be stitched on 2 sides, pulled off, put in pairs on the dress part 2, pulled off, equalizing on the sides, swept, stitched. Baste the drapery along the bottom and top of part 2. Next, sew the part as a single layer.
In addition, it is necessary to cut out 2 rectangles for a bow, 26 cm wide (13 cm in finished form) and 150 cm long (when tied, the width of the bow is 15 cm on each side of the knot).
The details of the belt are sewn into the sides of the dress and tied at the back with a bow.

OPTION 2
This colorful corsage dress is just made to win hearts: colorful prints, silk satin and draped details on the front of the dress are the main components of success.

Pattern modeling.

How to design and sew a dress.

On the front half of the dress, set aside 24-27 cm from the waistline upwards. Draw a horizontal line along the armhole line of the dress.
Set aside 4 cm down the front. Draw the line of the neckline of the dress according to the pattern.
Set aside 3 cm from the middle of the front of the dress along the waistline of the dress. From the right side of the chest tuck of the dress, draw a straight line to point 3.
From the left side of the chest tuck of the dress, draw a line of relief along the pattern.
Transfer the tail tuck of the dress to the center of the front. From the tail tuck of the dress, draw a line of the second relief along the pattern.
Cut off the front of the dress along the waistline.
Model the back of the dress as shown in Figure 2.
Additionally, build a draped dress detail. To do this, you need to measure the length along the waistline of the front of the dress. Set aside this value along the line.
The length of the detail on the side is equal to the length of the dress on the side from the waist to the bottom.
Shot the side of the detail from the side of the dress. Extend piece 20 cm down. Cut out 2 identical parts for drapery, sew them along the bottom, turn inside out and stitch. Then put the resulting part on the front of the skirt of the dress and sweep on the sides. Next, sew the skirt as a single layer.
In addition, re-cut the facing of the top of the dress with a width of 3 cm in finished form. In addition, cut out: a loop for a draped part 10 cm wide (5 cm in finished form) and 15 cm long (one end of the loop is superimposed on the waist section of the dress under the drapery part, the other end is bent over the draping part and superimposed on top).
From lining fabric cut out all the details of the dress, minus the facings.
Raised seams are reinforced with bones.

OPTION 3
It's small black dress, embroidered with rhinestones, will make you the star of any party! You can sew such a dress yourself if you follow our instructions.

Pattern modeling.

Since the model of the dress is very tight, there is no need to give an increase in the freedom of the fit.
On the front of the dress, move the vertical chest tuck to the middle of the front, model the neckline, transfer the tuck at the waist of the dress to the side of the dress.
Cut the front of the dress pattern along the horizontal dotted lines and spread 2-3 cm into the assembly.
Make the length of the dress according to your own measurements. (Including dress frill).
Model the frill of the dress additionally as shown in the dress pattern.
Model the part embroidered with rhinestones as shown in the dress pattern 3.
This part must be cut out additionally in 2 copies.
Strengthen one detail with thermal fabric, embroider with rhinestones or stitch ready-made motifs.
Model the collar of the dress additionally.
Model the back of the dress as shown in dress pattern 4.

IMPORTANT! This dress is gathered at the side seams for a very flattering fit. Therefore, fabrics should be chosen with elastic additives in the composition.

Additionally, cut out the lining (without additives for assembly at the seams).

How to sew a dress.

From the main fabric cut out:
Before the dress - 2 children.
The back of the dress - 2 children.
Dress frill - 2 children.
Dress collar - 1 child. with a fold + 2 children.
The central detail embroidered with rhinestones - 2 children.

Before the dress - 1 child. with a fold
The back of the dress - 2 children.

How to sew a dress.

On the sides of the front and back of the dress, lay lines with a stitch length of 4 mm. Pull to the desired length according to the pattern.
On the middle seams of the front of the dress and the back of the dress, lay lines with a stitch length of 4 mm. Pull off, pull up.
Sweep the side seams of the dress, stitch.
Sweep the middle seam of the front of the dress, stitch.

Sew the lining of the dress along the side seams and along the middle seam of the back of the dress to the zipper opening.
Fold the dress from the main and lining fabric face to face, sweep and topstitch along the top seam.
Turn the dress right side out, sweep clean at the top.
Strengthen the central part with thermal fabric. Roll up on the sides.
Put the detail on the dress, baste, straightening the assembly of the dress.
On the second part, tuck the allowances on the sides.
Combine the details with each other, put the second part on the wrong side of the dress on the lining, sweep.
Sew 2 pieces with one line to the edge.
Sew rhinestones and beads on the upper part by hand.
Sew the frill of the dress on the sides. Pull along the top of the frill.
Put on the bottom of the dress from the main fabric, bast, stitch.
Tuck the lining of the dress along the bottom and baste by hand, closing the allowances.
Tuck the bottom of the frill of the dress and topstitch.
Put the dress collar part reinforced with thermal fabric on the central part and sew.
Put the second part of the collar on top of the first and stitch along the top and sides.
Turn right side out, sweep clean.
Tuck the lower cut of the collar, bast, stitch.
Embroider the collar with rhinestones or ready-made motifs by hand.
Sew loops and hooks along the middle seam of the back collar.

OPTION 4
This dress is a real treasure! Such a dress can be sewn from iridescent gold satin with elastic threads, from taffeta and any other dress material.

Pattern modeling.

Since the dress is tight-fitting, allowances for freedom of fitting can be completely omitted or given the most minimal.
On the front half of the dress and on the back of the dress, transfer the tucks, as shown in the dress pattern. Model embossed seams along the lines of the tucks. Shorten the front of the dress and the back of the dress to the desired length of the skirt (without flounces).
The flounce of the dress is modeled separately. If it is not possible to cut out the frill of the dress without seams, you can make 2 seams that will match the side of the dress.

In addition, cut out the belt of the dress.

How to cut a dress.

From the main fabric it is necessary to cut out:
Dress detail 1 - 1 child. with a fold
Dress detail 2 - 2 children.
Dress detail 3 - 2 children.
Dress detail 4 - 2 children.
Flounce dress - 1 child. (or 2 children with a fold)
Dress belt - 2 children.
The details of the facing of the top of the dress completely duplicate the pattern of the dress to the waist.
Turning the details of the dress 1 - 1 child. with a fold
Turning det. dresses 2 - 2 children.
Turning det. dresses 3 - 2 children.
Turning det. dresses 4-2 children
The details of the facings of the dress must be reinforced with thermal fabric.

From the lining fabric, you need to cut out:
Details 1-4 minus turning.

Additionally, you need to buy bones for the side seams of the dress and the reliefs of the back of the dress.

How to sew a dress.

Baste and stitch the relief seams of the dress and the side seams of the dress.
The allowances of the side seams, taking together, stitch off 0.7 cm from the seam. Lay the line from the top of the bodice of the dress to the waistline of the dress.
Cut the bone to measure for threading into the resulting drawstring. The length of the bone should be 1 cm shorter than the drawstring. Insert a bone.
Re-stitch the drawstring along the top of the dress and along the waist line of the dress so that the bone does not fall out.
Sew a hidden zipper on the back of the dress.
Baste and sew a flounce along the bottom of the dress.
Strengthen the details of the facing of the top of the dress with thermal fabric.
Sweep dress facings with dress lining details.
Sweep side and embossed seams on the lining of the dress.
Fold the lining with the dress face to face. Sweep and stitch along the top and laces of the zipper.
Turn the dress inside out, sweep clean over the top and iron.
Tuck the bottom of the lining and baste by hand with hidden stitches, covering the sewing allowance of the frill of the dress.
Turn the flounce of the dress along the bottom and hem it manually with hidden stitches.
Sweep the dress belt and grind on all sides, leaving an open area for eversion.
Turn out the belt of the dress, iron it.
Sew up the open area by hand with blind stitches.
Put the belt on the dress along the seam and sew firmly to the dress with hidden stitches.
Tie a bow in front of the dress.

OPTION 5
This dress is for the young and brave!

Pattern modeling.

If you plan to sew a dress from an elastic fabric, then when building a pattern-base of the dress, do minimum wage freedom of fitting (1.5cm).

IMPORTANT! When modeling a dress, the front of the dress and the back of the dress must be completely redrawn on tracing paper.

The cutting of the dress must be done on a fabric laid out in one layer (except for the frill of the dress). It is necessary to cut out 2 identical parts of the frill, one for the back of the dress, the second part is the frill for the front of the dress.

OPTION 6
This lovely silk dress captivates, first of all, with its simplicity of modeling and execution.

Pattern modeling.

How to design and sew a dress.

On the front half of the dress, move the chest tuck to the side.
Shorten the tuck by 2 cm. Model the neckline, setting aside 24 cm from the bottom of the front neckline.
Flare the front of the dress on the side by 4 cm.
The back of the dress is modeled in the same way.
Draw a horizontal line from the bottom of the armhole. Cut off the top.
Move the tuck to the center of the back of the dress.
On the side, flare the back of the dress by 4-5 cm.
Additionally, cut out 2 strips of fabric for the bow: one 65 cm long and 20 cm wide (finished 10 cm), the second 70 cm long and 15 cm wide (finished 7.5 cm).

OPTION 7
This dress is a real dream! The dress is made of elastic satin, and its accent is unusual pleats along the skirt.

Pattern modeling.

Don't give any extra freedom of fit as the model is very tight.
Reshoot the pattern of the front of the dress on tracing paper completely.
Draw modeling lines on the bodice of the dress.
Cut off the excess at the top of the dress.
Flare the skirt as shown in the dress pattern.
The more you flare the skirt, the more fluffy it will turn out to the bottom.
Mark the squares on the wrong side of the dress pattern as shown in the pattern.
The length of the dress depends on the side of the square that you specify. Remember that when laying folds, we reduce their length by 2 times.
On the pattern, the length of the skirt of the dress from the line of laying the folds will be 40 cm (3 squares of 10 cm each (with folds) and 1/2 square along the bottom of the dress to align the bottom of the dress.
Model and mark the back of the dress in the same way.
The folds are not ironed, but are only swept along the blue dotted lines to the cover of the dress, which is additionally cut out according to the same pattern.
Then the folds are fixed with horizontal lines 5 cm long each.
The lining of the dress is cut 4cm shorter than the dress.

How to cut a dress.

From elastic satin it is necessary to cut out:
Before the dress - 1 piece with a fold
The back of the dress - 2 children.

From lining fabric:
Before the dress - 1 child. bend
The back of the dress - 2 children.

In addition, cut out a strip of fabric 8 cm wide and 30 cm long to make a rose.

IMPORTANT! The hidden zipper should not be long - only about 30 cm and should end up to the folds.

How to sew a dress.

On the front and back of the dress, use running stitches to transfer the markings of the folds to the front side.
Do the same for the lining pieces.
On the front of the bodice of the dress, cover the tucks. Stitch.
Sweep and stitch tucks on the back of the dress.
Sweep the dress along the side seams, stitch.
Sew the details of the lining of the dress in the same way.
Put on the dress and lining it face to face, sweep and stitch along the top of the bodice of the dress. Turn out, iron.
Sew a hidden zipper on the back of the dress.
Turn the dress inside out. Lay the folds according to the markup, stitching them to the lining of the dress with short horizontal seams (5 cm each).
Trim the excess lining so that it is 3-4 cm shorter than the dress.
Tuck the bottom of the dress and sew to the lining by hand with hidden stitches.

How to sew a rose

Fold a strip of fabric in half lengthwise and then twist in a spiral, starting from the center of the flower, fasten as the petals form with stitches.
Hide the edge of the strip under the bottom of the flower.
Sew a flower to the dress.
Decorate the bodice of the dress with ready-made motifs.

OPTION 8
Do you want to be the star of the party? Then, without hesitation, sew this dress for yourself!

Pattern modeling.

Give an increase in freedom of fit to the minimum - 1.5 cm.

Cut the pattern of the front half of the dress and the back half of the dress on tracing paper and model the bodice and skirt, as shown in the drawings of patterns 1 and 2.

Additionally, you will need to cut out 2 strips of fabric for the bow: one 20 cm wide (10 cm finished) and 80 cm long, the second 30 cm wide and 15 cm long (finished) and 60 cm long. The bow can be reduced at will.

OPTION 9
This charming dress is just made for noisy parties! And you should definitely sew this dress! After all, modeling it is very simple, the main thing is to make a little effort and you are a star!

Pattern modeling.

Allowances for freedom of fitting in this case are not given.
The width of the mesh for the skirt must be calculated as follows: The volume of the hips multiplied by three. The calculation given on the pattern is given for the Hips of the early 96cm.
The length of the mesh for the skirt is 80 cm (finished - 40 cm).
Mark the folds as shown in pattern 1.
Model the bodice of the front of the dress and the back of the dress as shown in patterns 2 and 3.
Additionally, you need to cut out the bottom of the dress from the lining fabric.

How to cut a dress.

From the main fabric cut out:
The middle detail of the bodice in front of the dress - 2 children. with bend
The side of the front of the dress - 4 children.
The side of the back of the dress - 4 children.
The middle detail of the back of the dress is 4 children.
Dress skirt - 1 panel
From the lining fabric, cut out:
The front part of the skirt of the dress - 1 child. with a fold
The back of the skirt of the dress - 2 children.

Additionally, cut out a belt, 8-10 cm wide (4-5 cm in finished form), and 100 cm long. Flare the ends of the belt by 2-3 cm.

How to sew a dress.

Details of the bodice of the front of the dress and the back of the dress should be strengthened with thermal fabric.
Sweep and stitch the details of the bodice in front and back of the dress along embossed seams. Stitch.
Side seam allowances only, stitch together at a distance of 0.7 cm from the connecting seam. Insert a bone into the resulting drawstring, 1 cm long shorter than the side seam without allowances.
Lay folds on the skirt of the dress from the main fabric, as shown in the pattern. Ideally, you should get a ball of folds.
The calculation of the grid is done on the volume of the hips, therefore, at the waist, each fold must be laid a little further than the intended line.
The same can be done on the bottom of the dress, then the shape of the skirt of the dress will look more like a ball.
To keep the folds well, make short bartacks on each pleat that will hide under the layers of fabric.
If the above diagram does not suit your figure, you can lay folds in a chaotic manner right on the mannequin.
Sweep the bottom of the dress and the top of the dress. Sweep a zipper down the back.
Try on and make adjustments as needed.
Sew on a hidden zipper.
Sweep and stitch the details of the bodice from the main fabric (dress lining) without strengthening with thermal fabric.
Sweep and stitch the details of the dress skirt from the lining fabric.
Connect the top and bottom of the lining of the dress, sweeping and stitching along the waist seam.
Apply face to face the main product and the lining of the dress.
Sweep and stitch along the top of the bodice of the dress.
Sweep and stitch the dress and lining along the bottom.
Turn the dress right side out through the open area, sweep clean at the seams.
Tuck the zipper allowances and sew by hand with a blind seam.
In addition, sew a belt for the dress. To do this, you need to cut out 2 parts 4-5 cm wide and 100 cm long.
The ends of the dress belt have a flare of 2-3 cm.
Place the details of the dress belt on top of each other face to face.
Sweep and stitch on all sides, leaving an open area for eversion about 5 cm.
Turn the belt out, sweep it cleanly, stitch it.
Sew up the open section of the belt manually with a hidden seam.

The following models are developed on the bases calculated in the Cutter program.
You can download a demo version of this program.

OPTION 10
The dress is tight-fitting at the waist and narrowed to the bottom of a non-stretch dress fabric. Ahead is a bolero with a jacket collar and lapels. Shoulders are slightly slumped. Asymmetric fastener with a hidden zip moved to the side seam. The lapel of the shelf is stitched to the fold of the lapel of the bolero. Back with reliefs from the armhole and a slit at the bottom. Under the dress is a corset with lace trim.

Model processing technology

Stitch the zipper into the left relief of the shelf up to the fold line. Overstitch the edges of the relief cuts and the lapel with overturns, turn right side out and baste the edges. Unscrew the flyaway part along the fold, bast to the shelf and overcast the open sections together. Stitch the side tuck on the shelf and stitch the relief of the shelf. Stitch the edge of the side and the ledge of the lapel of the bolero with a lining. Stitch the armhole of the bolero from the shoulder to the notch. Turn the details of the bolero right side out. Stitch the armhole of the bolero from the notch down with a relief. Stitch the right shelf to the bolero. Stitch the middle seam of the back, darts from the shoulder and reliefs. Stitch the armhole of the back with a stitch. Stitch the shoulder seams of the top and lining. Stitch the side seams by inserting the cuts of the front and the bolero between the cuts of the back and the facing of the back. Process the collar and sew it into the neck. Process the bottom of the product.

OPTION 11
Dress of an adjacent silhouette with one sleeve, cut in the middle, and a shoulder strap. A bodice with an asymmetrical bottom in front, the back is lowered from the waist. On the back there is a zipper. The skirt is flared.

Since the dress has an asymmetric shape, it is necessary to have 2 sets of bases and build the right and left parts of the front and back separately. On the right and left shelves, transfer the shoulder tuck to the side cut. Glue right and left shelf along the front cut and apply model cut lines along the top and bottom of the front of the bodice. On the left back, mark the width of the shoulder equal to the width of the shoulder in front from point P along the line, because draw the back in this model without a tuck and draw the armhole line from point P to P3. Apply model cut lines on the left and right back. Measure the length of the shoulder strap at the front and back. Cut the sleeve in the middle and expand the front and back of it.

OPTION 12
Evening dress in soft jersey, tailored to the figure, with a large neckline, falling flounces, high side slit, with long sleeves collected at the wrist. The evening dress is designed on the basis of a dress of an adjacent silhouette with a single-seam sleeve without a tuck.

To model this dress, you need two sets of patterns and increase the length of the sleeve by 10 cm.

On the shelves, transfer the shoulder tuck to the side cut. Connect two shelves along the middle cut and apply model lines. Cut off the right side of the shelf. Mark cut lines on the right side of the shelf.
Cut out the allowance for the tuck and cut the right side of the shelf along the marked lines without bringing the cuts to the side cut by 0.5 cm. Move the cuts at the same distance from each other, while closing the side tuck. Circle the resulting pattern and cut it out.

On the back, close the shoulder tuck, for this, draw the line of the shoulder from point A2 to point P and draw the armhole from point P to point P3. Deepen the back neckline. Draw the shuttlecock in the form of a spiral. The length of the inner spiral is equal to the sum of the lengths of the neck cut and the shelf cut. The width of the shuttlecock at its widest point is 15 cm.

Gather the sleeve at the bottom along the sewing seam.

OPTION 13
Evening dress in brown chiffon with satin lining Pink colour. Top with feminine draping. Strongly flattering cut. Bodice with an undercut in the middle of the distance from the chest line to the waist line. Skirt full sun. Cuts of an armhole and a mouth are processed by an elastic band. In the side seam there is a fastener with a hidden zipper. All sections of the top and lining are ground at the same time, only the chiffon skirt at a distance of 10 cm from the bottom is ground without lining.

Based on the dress of the adjacent silhouette, cut off the bodice along the outlined relief line. On the shelf, close the tuck from the shoulder. On the shelf and back, mark the location of the cuts of the neck and armholes according to the model. On the lower parts of the shelf and back, close the waist darts. These are the details of the excellent lining. Chiffon details should be 1.5 times wider along the shoulder and bottom sections, as well as along the side sections of the lower parts of the shelf.

Open flared skirts "full sun" on the fabric:
The radius of the notch at the waist is St / 3. On an oblique thread, reduce the notch at the waist by 1.5 cm. From the waist, with the help of auxiliary segments equal to the length of the skirt with an allowance for processing, draw the line of the bottom of the skirt.

Fabric consumption for a flared skirt "full sun":
L = 2R + √ (2R)2 - W2

where:
L - web length
R is the radius of the circle
R \u003d St / 3 + skirt length with processing allowance
W - web width

OPTION 14
The evening dress is made of thin knitted fabric. Ahead is a deep neckline, reliefs from the armhole. The bodice of the back consists of three parts triangular shape. At the end of the upper part of the bodice there is an air loop of 2 cm. The side parts of the bodice of the back end with ribbons, which are threaded into the loop of the upper part and tied. The back skirt consists of two parts.

The model was developed on the basis of a dress of an adjacent silhouette, in which all allowances are reduced to zero for a tight fit.

OPTION 15
The dress is adjacent along the bust line and extended from top to bottom from crepatlas. Folds are laid in front, in the folds of which ruffles are sewn. On the folds of the folds to the bottom are laid finishing stitches. Soft folds on the sleeves. At the bottom of the sleeves and between the folds, glass beads are sewn, shimmering in subdued light.

The model was developed on the basis of a straight-cut dress with a one-piece sleeve. In the measurement "Length of the arm to the first joint of the thumb" (Dr1s), you must enter the length of the sleeve for this model, namely to the elbow. Enter the shoulder girth value at the top Opv into the Opv measurement. Pb=5, Popv=20, Pozap=10 cm.
On the shelf, outline the lines for stitching the ruffle, cut the base along these lines and push the details 2 cm apart. The dotted line marks the facings of the neck of the shelf and back.

Model processing technology

Ruffles are processed with a zigzag stitch with a double hem of the cut, preferably with a snail foot. Finish the end cuts with a seam in the hem. Overcast the front and back sections except for the shoulder sections, neckline sections and armholes. Bend the bottom of the shelf and stitch at a distance of 2 cm from the fold, leaving 5 cm unstitched from the side cuts.

Mark the fold lines of the folds on the shelf. Baste ruffles to the folds of the folds to a depth of 1 cm. Sew the ruffles with a seam 0.5 cm from the fold of the fold and continue stitching to the bottom.

Baste the ruffles to the shelves and stitch them onto the shelves by laying a line in the stitching line of the ruffles. Overcast the neckline and overstitch the neck of the shelf with it. Sew the seam on the facing 1 mm from the fold. Iron the facing on the wrong side, securing it along the shoulder section. Sew back seam and iron. Overcast the facing and overstitch the neck of the back with it, leaving the allowances of the shoulder seams unstitched. Sew overturn seam to overturn 1 mm from the fold.

Put the shoulder sections of the shelves together with the piping between the shoulder sections of the back and the piping of the neck of the back, stitch the shoulders and overcast from the side of the shelves. Iron the facing of the neck of the back inside out. Stitch the side cuts and iron. Turn the bottom of the back over and stitch at a distance of 2 cm from the fold. Overcast the sleeves, except for the cut of the hem. Lay the folds in the direction indicated on the drawing. Lay folds in the middle of the sleeves and fasten them with a zigzag stitch of 4-5 punctures in one place. Sew glass beads on the sleeves. Stitch the side sections of the sleeves, hem the sleeves. Sew the sleeves into the armholes and overcast the stitching seams from the side of the front and back.

OPTION 16

Dress in soft crepe satin. The bodice is loose with one-piece sleeves. The collar is double, so that the dress rests on the shoulders, an openwork braid is laid at the back. The skirt is slightly tapered at the bottom. Wide belt with bow tied twice.

The model is designed on the basis of a dress with a straight silhouette. The body position is 0, Pk=0. The chest undercut is closed from the shoulder, and open from the waistline. The bases of the bodice of the front and back are connected so that their middle cut is on the same line. Distance |A4,H| equal to the length of the sleeve plus the width of the shoulder slope "Shp". The model is cut without middle and shoulder seams.

OPTION 17
Dress of an adjacent silhouette from chiffon on a lining. The lining of the bodice is duplicated. Fastening on the side with a hidden zipper. The length of the dress is from the short side to the middle of the calf, with a length to the ankle. The figure-hugging cut makes her slimmer.

The model is developed on the basis of a dress of an adjacent silhouette. Printed two sets of patterns. On both halves of the shelves, tucks are closed from the shoulder, and open from the side sections. Shelves and backs are connected vertically, then all the constructive lines necessary for the model are applied, taking into account that the shoulder width of the bodice in the cut should be twice as wide as in the finished form. The skirt consists of two wedges, the shape and method of cutting which are shown in the drawing.

OPTION 18
Strongly flattering cut. Seam at the waistline and under the bust. The top part of a bodice with a drapery. The lower part of the bodice tightly fits the figure. The shoulder is lowered, in front there is a deep neckline. Flared skirt". Length 6 cm below the knee.

The model is developed on the basis of a dress of an adjacent silhouette. Mark the cut line on the shelf. Move the shoulder tuck to the bottom edge of the top of the shelf. Lengthen the shoulder by 5 cm and draw a new armhole shape. Mark the shape and depth of the cut. Draw the lower part of the shelf horizontally, shortening it by the amount of the tuck. Mark the cut line on the back. Draw the shoulder line from point A2 to point P in a straight line and continue the shoulder by 5 cm and draw a new armhole shape. Mark the neckline and middle back. Cut the lower part of the backrest horizontally by the depth of the tuck.

The flared skirt is built according to the calculations below:
OT \u003d St * 1.4 - the radius of curvature of the waist line.
TB \u003d Dts / 2 - the distance from the waist to the hips.
TH = skirt length
TT1 = St + Fri
BB1 = Sat + Fri

Where:
Dts - the length of the back to the waist.
St - semi-circumference of the waist.
Sat - half-circumference of the hips.
Fri - waist allowance.
Pb - allowance for the hips.

OPTION 19
Dress in fine jersey with a satin effect. The top of the dress is straight cut. The skirt is two-layer, tight-fitting figure. At the top of the back there is a zigzag stitched elastic band. An elastic band with a zigzag stitch is sewn on the stitching seam of the bodice and skirt.

The model is designed on the basis of a dress with a straight silhouette. It can be performed without side seams on the bodice by connecting the sections.

OPTION 20
Knitted dress fitted silhouette, sleeveless, high shoulder line. Asymmetrical neckline. Strap on one shoulder, thick gathering on the other.

The model was developed on the basis of a dress with a fitted silhouette without any allowances for a loose fit. Connect the drawing of the right and left shelves along the half-skid line and cut the drawing from one highest point of the chest to the other and cut out the middle part from tuck to tuck. Close the right tuck from the shoulder by turning the cut out part of the drawing around the highest point of the right chest. Connect the highest point of the neck to point A7 on the left side of the drawing with a convex line. Make a neck according to the model. Narrow the shoulders to the desired shoulder strap width.

OPTION 21
Fitted dress in crepe satin silver color on a lining, along the bottom of which a black frill is sewn. The detachable yoke is assembled under the jumper.

The model is developed on the basis of a dress of an adjacent silhouette. Shoulder tuck moved to the middle section of the shelf.

Stitching on this design long dress, but without the frill at the bottom, you will get a lovely evening dress.

Model processing technology

Glue the straps and the lower parts of the trim strips with interlining. Stitch the jumper along the side cuts and turn right side out. Stitch the middle section of the yoke to the front side. Stitch the tuck on the yoke to the front side, after inserting the jumper from the wrong side into the seam. Bend and stitch the bottom of the flyaway yoke.

Assemble the top of the trim strips. Stitch the trim along the top side seam. Turn the strips right side out and secure with a stitch along the bottom and side cuts. Stitch the strips between the shelf yoke and the detachable yoke at a distance of 4 cm from each other. Fasten the lower section of the jumper behind the seam of the coquette tuck from the front side. Overcast the shelf and the lining to it.

Stitch the yoke to the front, inserting it between the front and the lining. Overcast the sections of the back and lining to it. Stitch the middle seam of the back and iron. Stitch darts on the back. Stitch the top edge of the back with a lining. Insert the elastic between the back and the lining and topstitch it with a zigzag stitch.

Stitch back straps and turn right side out. Stitch the front straps along the outer edge, inserting the back straps into the neckline. Sew the front straps along the inner edge to the seams for attaching the yoke and turn right side out. Sew straps in front to front side coquette.

Sew the side sections of the front and back along with the lining to the waist, and then separately the sections of the dress and lining. Turn the front straps from the wrong side and topstitch them near the stitching seam. Process the frill, stitch it to the bottom of the lining. Hem the bottom of the item.

If the model seemed simple to you, then you are mistaken)) See what you can create from this pattern:

OPTION 22
Dress in a thin jersey fabric with a tight fit. The parts of the bodice are intertwined, the straps on the back are twisted. On the side and back sections on the wrong side, an elastic band (elastic band) is sewn in a zigzag stitch.

The model was developed on the basis of a dress of an adjacent silhouette with a preliminary increase in the values ​​of the vertical measurements of the figure, namely: chest height - Vg, front length to the waist - Dt.p, back length to the waist - Dt.s, oblique shoulder height - Vp.k, length sides - dB, all 1.3 times. Allowances for freedom of fitting Pg, Fri, Pb are equal to zero. Connect the upper and lower parts of the bodice by turning the upper part, as indicated by the arrow.

Model bodice processing technology

Straight upper cuts and lower cuts from notch to notch of both parts of the bodice are sewn into a hem with a closed cut. Sew the right side of the bodice along the lower cut to the notches. Pass the left part of the bodice into the hole formed in the right part of the bodice after sewing and sew to the notches. Stitch the bodice to the shelf.

OPTION 23
Lined crepe satin or chiffon dress with a body-hugging fit. A fastener on a secret lightning in a back. The top of the dress is trimmed with bias tape from the main fabric. The model was developed on the basis of a dress of an adjacent silhouette, a recess on the chest from shoulder cut moved to the side cut.

OPTION 24.
Highly beautiful model tunics are sewn as easy as shelling pears. Suitable for a cocktail dress, for pregnant women and luxurious women.

OPTION 25.
Pattern-basis of a dress for ladies with appetizing forms + 2 patterns cocktail dresses and lots of ideas, including evening dresses!
Watch and

OPTION 27. Corset dress!
Watch .

OPTION 28. In this magnificent dress you will be the queen of any evening!
Watch .

OPTION 29. Gorgeous satin dress!
Watch .

OPTION 31. Evening satin dresses!
Watch .

OPTION 32. Strapless dresses!
Watch .

OPTION 33. The sexiest and easiest dress to make!
Watch and .

OPTION 36. Dress with drape at the neck!
Watch .

fashion review evening dresses of leading fashion houses! Season 2011-2012!

Many women, as an outfit for New Year choose exactly the dress. In our mind, no suit or crazy stylish trousers, combined with a blouse, will not emphasize your femininity and sexuality like a dress! So what kind of dress can you wear for the New Year?

Fashionable dress for the New Year 2012 - fabric
Having decided on the model, take the choice of material from which your festive masterpiece is woven no less seriously. It can be silk, satin, etc., but the undisputed leader fashion shows- these are dresses made of velvet: luxurious, flowing, a bit reminiscent of the water surface.

Fashionable dress for the New Year 2012 - color
The mega trendy palette today is headed by the alluring and bewitching color of silver and gold, as well as all shades of gray, beige, sand, bright red and deep purple and, of course, stylish black and chic white have not sunk into oblivion.

Cocktail Dress
Are you the owner of chic, slender legs, and you certainly want to demonstrate your pride to others? Then you should opt for a sexy, short cocktail dress - this is an ageless classic that can be presented in a new way by playing a little with the material. For example, a short lace dress will create a unique seductive, light look. Designers also offer us luxurious dresses embroidered with crystals (Givenchy collection, Donna Karan).

Dress to the floor
If you want to make a lasting impression, you just need to try on a floor-length dress! Nothing will add chic and luxury to your look like a long dress. At the same time, it can be without a deep neckline, but with an almost indecent cutout at the back ... The New Year is all about surprises, and your bare back will be a pleasant, alluring surprise for your companion! If you are not ready to expose the most graceful part of your body so much, designers suggest that we use lace inserts.

Dress - "fish"
For owners of a slender figure, designers offer to give their preference to a fish dress. In this model, you will feel like a world-class star on the red carpet before the Oscars.

Compilation simple models With simple patterns, which even beginners can handle. Without spending a lot of time in an hour and a half, a new new thing is ready!
Spectacular dress
A light dress pattern, which, if desired and with a wide belt, can unexpectedly turn out to be a tunic that is not a sin to wear with tight black trousers and high platform shoes. Believe, sew Short dress A beginner with no sewing skills is quite capable!
to photo hosting →
This pattern for a girl with a height of 164-170 cm and a size of 46,48,50 will require 100 cm of knitted fabric with a width of 150 cm. Although, if desired, you can always redo this pattern to any size. Skirt length 34 cm to the middle of the thigh, on original photo the length of the skirt is about 45-50 cm and a piece of fabric, so you need to take 15-20 cm longer.
to photo hosting →

Fold the fabric right side in, pin along the edge, fold and a few pins scattered throughout the fabric. Step back from the edge of the edge 1-2 cm, grind the line and cut the edge along this 1 line. Again, retreat 1.5-2 cm from the cut and draw a line, this is the middle of the back.
Depart from the upper cut 1.5 cm and draw a horizontal line, on this horizontal line from (.) A to the left, mark the points after 11 cm and after 34 cm (.) B.
From the point (.) A down the fold after 56 cm, mark (.) B, and from (.) B to the left horizontal, on it 24 cm (.) E and after 36 cm (.) D.
From (.) B down the vertical is 33 cm, and from (.) D to the left the vertical is 10 cm.
From (.) D vertical up to the intersection with the horizontal from (.) D. Make a conjugation.
From (.) G up, mark 2 cm and smoothly connect with (.) E.
It remains to build a neck-boat and the upper part of the shelf is ready. From (.) And set aside 4 cm down and smoothly connect with a point of 11 cm.
Now, before continuing further construction, you need to draw allowances for the seams. On knitwear, a 1 cm allowance is enough. Draw allowances along the shoulder seam, neckline, armhole, side seam and bottom.
Next, you need to build a skirt. Step down from (.) Г 2 cm and from this point draw a horizontal line equal to one quarter of the measurement of your hips minus 2-4 cm (this value depends on the extensibility of the knitwear, the more it stretches, the larger this number, but do not worry, since the fitting will decide everything.) From this point (.) down the vertical.
Further along the fold down the desired length of the skirt, I want 34 cm and from this point to the left the horizontal until it intersects with the vertical.
From the conditional (.) B (conditional because we retreated down 2 cm) to the left one quarter of your waist measurement minus 2-4 cm. I have it 19. I wanted to make the waist line 2 cm lower, respectively, the measurements have changed.
Connect point 19 with a smooth curved line to the side seam. On the fitting, the side seam is adjusted. Draw 1 cm seam allowances along the waist line and side seam, 3-4 cm seam allowance along the bottom.
Cut out the front and skirt. Attach a shelf to the opposite upper cut, chop, grind. Don't rush to cut. First you need to draw the neck of the back in accordance with the drawing. Put on the skirt, pin and cut out the details of the back and skirt.
Product assembly.
There is a seam on the back, and there you can leave a small incision and make air loop. Stitch back seam. Process the neck of the back and shelves. Connect shoulder seams. The length of the seam to your taste is 5-7 cm or more from point 11. Connect the side seams, the bottom of the sleeve from (.) B by 4-5 cm. Process the bottom and the cut of the sleeves. Connect the side seams of the skirt. Stitch the middle seam of the skirt and, if you wish, make a slit for comfortable walking. Make an assembly on the back and shelf of the bodice. Pair with a skirt. Process the bottom of the skirt. The dress is sewn with a knitting needle, a zigzag stitch or a special knitted stitch.