Hello my dear blog readers. I haven’t written complex articles for a long time, and in my opinion, today is exactly like that. We'll consider building a blouse pattern, in fact, if you look, then tailoring blouses and shirts has a lot general principles They just need to be understood once. And if you build a blouse pattern for yourself once, then you can then adjust it a little and sew a huge variety of models of blouses, shirts and tunics.

Exactly the same principle was when we built a pattern for the base of the dress, so that later we could sew any model for ourselves with a perfect fit on your figure.

Today we will consider building and modeling such a blouse, with a stand-up collar, turning into a bow:

This model is built on a pattern basis without tucks, free models are cut out on its basis, such as men's shirts, etc.

I will now describe step by step the construction of the pattern, your task is to substitute your measurements.

I immediately give an increase, which I will add to my measurements, the increase is the same for everyone.

Additions:

Pb = 2.5 cm (if we tuck in the blouse) and 3.5 cm (if the blouse is worn over the skirt)

Shoulder extension = 0.5cm

T 1 T 11 - lowering the waist line in front = 0.5 cm

Item Length = Hips

Blouse fabric. How to decide?

For this blouse, thin cotton, cambric, poplin, chiffon is suitable.

Finishing fabric: satin, satin.

Building a base - grids

The grid is a designation of the location of the main horizontals in the drawing - the lines of the chest, waist, hips, the width of the grid = the girth of your body (more precisely, the upper body).

For the drawing, we take graph paper. Place A in the top left corner.

1. AT Down = Dts + 1 = 38 + 1 = 39
2. AG down \u003d Vprz + Pspr \u003d 20 + 3 \u003d 23
3. TB Down = Dlb = 20
4. TT 'right \u003d 1.5 (this is a constant value, set aside for the fit of the model on the back), we draw a straight line through point A and T '. We put points G ', B '.
5. G'G1 right we set aside the width of the grid \u003d Cr3 + Pg \u003d 45.5 + 5 \u003d 50.5
6. G'G4 to the right - side seam \u003d G'G1 divided by 2 \u003d 25.25
7. Armhole width \u003d 0.25 times (Cr3 + Pg) + 1 \u003d 0.25 times (45.5 + 5) + 1 \u003d 13.6. From the point G4 to the right and to the left, set aside half the width of the armhole (half of 13.6) = 6.8 cm

Back construction

1. AA2 right \u003d 0.33 times Csh + Pshgs \u003d (0.33 times 18) + 1 \u003d 7
2. A2A21 down = 0.33 times AA2 + Pvts = 0.33 times 7 + 0.2 = 2.53
3. A2 put aside 9 to the right. This is a constant value for everyone. Point 9
4. From point 9 we set aside 2 cm down (this is also a constant value). We carry out the slope of the shoulder.
5. A2P1 down the slope to the right \u003d Shp + shoulder lengthening \u003d 13 + 0.5 \u003d 13.5. Point P1 should go beyond the armhole line by at least 0.5 cm. If the shoulder width is small (like mine = 11), then add the missing length to the shoulder width.
6. We build an armhole: 1) Point P3 \u003d G2P is divided by 3 + 2 cm (constant value) up; 2) Bisector from point G2 = 0.2 times G2G3 + 0.5 cm (constant value) = 0.2 times 13.6 + 0.5 = 3.2. We draw the line of the armhole of the back through these points.

Building the front

1. T1T11 down = 0.5 cm = B1B11 down
2. T11A11 up \u003d Dtp - 1 \u003d 44.5 - 1 \u003d 43.5
3. A11A3 left = AA2 (take distance from backrest drawing) = 7
4. A11A4 down = AA2 + 1 = 8
5. From point A3 to the left 9 cm. From point 9 we lay down 3 cm. We draw a straight line through points A3 and 3 - the slope of the shoulder.
6. A3P5 set aside by the slope of the shoulder = A2P1
7. Front armhole: 1) Point P4 = draw a perpendicular to the straight line from point G3;) Find point P6. \u003d G3P4 divided by 3. Point P6 is on the bottom 1/3 .; 3) Bisector from the corner = 0.2 times G2G3 = 3.2 cm

Hip Width

1. G'G4 \u003d B'B21 set aside on the horizontal line of the hips
2. We calculate the lack of width along the hip line: (Sb + Pb) - G'G1 (mesh width) \u003d (48 + 2.5) - 49 \u003d 1.5 cm - this is the lack of width along the hips. So the width must be added, otherwise the blouse on the hips will be small. We divide this difference by 2 (in my case it is 0.75 cm each) and set aside 0.75 cm from points B21 to the right and B2 to the left. We put points B "2 and B" 21.
3. we connect the point G4 with B "21
4. we then connect the point G4 with B "2.
5. We draw the bottom line along the back perpendicular to the retraction line (AB ')
6. Calling side cuts blouses: G4B"21 = G4B"2
7. We draw a bottom line along the front of the blouse, but since point B11 is 0.5 cm lower than the level, we draw a bottom line under the pattern.

On this, the basis for constructing a blouse is over. Next, we will do the modeling of a given model, but other models of blouses can also be built on this basis.

blouse modeling

Now we will analyze the main points of changing the drawing in order to get exactly the model as in the photo.

Button placket

We cut off from the drawing of the product parallel to the center line in front of half the desired width of the bar. My plank width is 3cm.

1. B11B’11 left = 1.5 cm
2. draw a vertical through point B'11 upwards
3. put point A41

We draw a bar 3 cm wide and long = B’11A41 next to the drawing

IMPORTANT! if the bar is stitched, then the loops on it can only be vertical, if the bar is one-piece, then the loops can be horizontal

We place the location of the loops on the bar:

The first loop is 1.5 cm below the top cut (this is the standard). Then we determine the number of buttons, determine the distance between the loops and mark the upper edges of the loops.

In this case, the distance between the last loop and the bottom line should be greater than the distance between the loops.

Buttonhole length = button diameter +3 mm

Stand collar with ties

We mark on the drawing the control point of stitching the collar into the neck: from point A41 we set aside 2 cm to the left. We set the control point.

To determine the length of the collar, measure the length of the neck.

Collar length = (Back neck length + Front neck length to the reference point + 50 cm for ties) x 2 = (7.8 + 9.5 + 50) x 2 = 140

Collar width desired. I took 6 cm.

At the ends, the collar has an extension - 9 cm. We expand the collar to the desired width at the ends.

The collar is a straight strip of fabric, cut along the transverse thread, we do not glue it with doubler.

TURNS

We decorate the facing of the blouse on the details of the front and back in the neck area. The width of the facings is 4 cm.

Reducing shoulder length

It is necessary to reduce the length of the shoulder along the front and back to measure Shp + 1 cm = minimum lengthening of the shoulder so that the sleeve visually looks in its place. Cut off excess to points P3 and P6. In the drawing, this area is shaded on the shoulders.

Fabric layout:

Flap pockets

Modeling valves. Front decor.

• On the details of the front, we mark the level of stitching of the valve - 4 cm above the level of the armhole. From the point G1 we set aside 4 cm upwards and draw a horizontal line.
• From the plank line on this horizontal line, set aside 5 cm to the left. This is the beginning of the valve.
• Valve length 9 cm.
• Flap width 5 cm.

Shaped corners.

The flap should not reach the armhole line at least 3 cm.

We cut out 4 parts so that the inside of the valve is not visible from the front side, you need to make the inner half of the valve a little smaller. We do this with allowances. On the outer part of the valve, the allowances are 1.3 cm, and on the inside - 1 cm, when sewing and turning to the front side, the inner part will not be visible, and it will be more beautiful.

Read about the construction of a sleeve pattern at the link. I will write about the stages of sewing a blouse a little later)).

Sew with me) and inspiration to you))))!

The blouse is indispensable attribute basic wardrobe, which is simply a must for every self-respecting fashionista. Blouses come in different styles and colors, so everyone will find exactly what suits her taste.

It is absolutely not necessary to spend a fortune on an original thing, because you can sew it yourself. In this article we will talk about how to make a blouse with our own hands and talk about the features of its tailoring.

Irreplaceable pattern

It is easiest for beginner tailors to sew a blouse according to a pattern. The simplest patterns may include only one piece, for more complex styles, you will need to build several pieces.

We will tell you: how to build a blouse pattern with your own hands. The blouse pattern is similar to the dress pattern with darts, but with changes made:

• Initially, copy the scheme of the basic base to the waist line.
• After we cover the tuck on the chest and begin to draw cuts from the middle of the chest to the center of the shoulder and the middle of the armhole. Next, cut it down to a point showing the center of the chest.
• We draw the front and back separately on paper sheets so that the vertical and horizontal lines intersect. So we get the center of the part and the waist line.
• We place the blank of the front element in such a way that the vertical line should connect to the dot in the middle. And the bottom point should be crossed by a horizontal line.
• The backrest element should be placed in the same way.
• Then we draw on the back of the blank element shoulder line in accordance with the cutouts.
• We lengthen the line of the shoulder so that it is equal to the shoulder level of the back.
• Set aside 0.5 cm outward from the central level of the armhole.
• On the side, we deepen the armhole by about two centimeters. From there we draw a line at an angle of 90 ° to the front line.
• From the waist line down, set aside approximately 17-19 cm and draw a bottom line at a right angle.
• We make an armhole.

Is it possible without a pattern?

A do-it-yourself blouse without a pattern is sewn literally in one day and does not bring a lot of trouble to tailors, on the contrary: sewing such a new thing is a pleasure.

• Fold the fabric in half twice with the right side inward.
• Now we make marks on the fabric. From the fold line to the bottom we measure about 2-2.5 cm, and to the side 9-10 cm. This is how we get the neck
• From the resulting neck, measure the length of the shoulder and sleeve. From this line we measure 2-2.5 cm and draw a line to the neck from the end of the sleeve.
• We need to divide the circumference of the hips and waist by 4. To postpone the resulting unit of measurement along the lines of the waist and hips.
• Connect the bottom and sleeve of the product with an indirect line. Let's cut out what we got.
• Cut the front of the neck slightly lower than the back.
• We sew the elements of the part and process the edges.

That's all. A beautiful simple blouse with your own hands is ready!

summer blouse

In the wardrobe of every fashionista, in case of warm days, there is a summer blouse. It is usually sleeveless, and sometimes has short or 3/4 sleeves.

Typically, light, flowing materials such as chiffon and silk are used for such a blouse. The color scheme of blouses for summer is light, pastel, bright.

Chiffon is in fashion!

Chiffon blouses, which look light and very refreshing, are now back in fashion. They got their special place on the fashion catwalks around the world. Chiffon blouses are best chosen in a loose style, because chiffon does not stretch at all.

And if you prefer models with a fitted cut. then pay attention to chiffon blouses with fasteners. These blouses will look great with skirts or trousers.

Men's shirt to help

Did you know that from men's shirts you can sew a beautiful and incredibly feminine blouse. We will tell you how to make a blouse from a men's shirt:

• First, we will narrow the sleeve. That is, let's try on a shirt and make a mark where our shoulders end.
• Let's put things on the table. And draw a curved line along the seams of the thing from the shoulder to the armpit. Fold the product and cut exactly along the lines.
• Turn the shirt inside out. We pin the sleeves to the shirt with pins (right to the right side, left to the left. Sew the sleeves to the shirt.
• Let's try on a shirt turned inside out. We draw a curved line to the side under the chest. With the help of a ruler, we extend the line to the very edge of the thing.
• Carefully symmetrically redraw the tuck on the other side of the thing. We mark our tucks with safety pins. We sew them immediately under the drawn line.
• Trying on. If you are satisfied with the result, great! If not, then redo it. Be sure to iron the seams of the tucks.
• We put our thing on the table. We draw a curved line from the armhole to the cuff and from the armhole to the bottom of the product. The expressive element of the bend is the waist.
• Cut out according to the lines. Pinned with pins and stitched.
• Iron the seams and try on.

So, we got a wonderful blouse from a men's shirt.

We wish you creative inspiration and the most fashionable new things!

It is not difficult to sew a beautiful, fashionable and comfortable blouse. If you have a sewing machine and little skills in working on it, you can diversify your wardrobe with trendy things that will also be exclusive.

Fabrics for sewing blouses

Blouses of a free silhouette made of flowing fabrics, such as chiffon, look extremely impressive. For a slender woman, simple blouses made of transparent fabrics such as organza that hold their shape are suitable. However, such materials require special processing. For an inexperienced dressmaker, at first it is better to choose cheaper fabrics. For summer, cotton, such as gauze, is suitable. It is easy to sew from it, and things look very beautiful and feminine. Learn to sew comfortably on linen fabrics. A T-shot blouse pattern with straight cuts along the bottom of the shelves and sleeves can become an element for sewing a stylish set. The product can be decorated with a fringe of elongated threads, pick up jewelry in ethnic style and wear with jeans, long skirt or short shorts.

Modeling Options

The light blouse pattern that we offer in this article can serve as the basis for modeling. You can change the shape of the neckline by making a large triangular neckline on the back, and not a shelf - a boat.

Sleeves can be finished with a wide bell or fluffy frill, but you can make cuffs.

Removing large allowances for a loose fit, adding vertical darts and inserting a zipper into the side seam, you can make a blouse of an adjacent silhouette. In this case, it is recommended to choose fabrics with elastane.

The bottom of the shelves can be made multi-level straight or rounded. If the allowances of the side seams are made by 2 cm, then this will allow you to make beautiful cuts along the bottom of the blouse.

Features of tailoring according to simplified patterns

Quick patterns of blouses for beginner dressmakers are very convenient, as they do not require an exact fit. And this is very important when it is not possible to use outside help during the fitting. Famous couturiers do not ignore the simplest patterns of blouses such as those presented in the article. Using such patterns, they focus on the quality, texture and stuffing of fabrics.

The simplest blouse patterns can consist of just one piece. Take a look at our proposed scheme. Numerous exact measurements are not needed for its construction. For a standard figure, it is enough to know the circumference of the chest, the length of the product and the length of the sleeve. These measurements are also needed to determine the amount of tissue. Usually, for sewing a blouse with a fabric width of 1 m 45 cm, one blouse length and one sleeve length are required.

Blouse for any figure

Such a blouse can be sewn in one evening. It has only two seams. She puts it on over her head.

A blouse requires 1.5 m of fabric with a width of 145-155 cm. It can be cotton satin, silk chiffon or other softly draping material.

You will need a blouse pattern. Here is a pattern made for 38-40 sizes. (chest circumference 88-92 cm). The model is supposed to be made of thin fabric, free silhouette, with a large allowance for a free fit.

If your size is larger, then you need to increase the width of the blouse by shortening the length of the sleeve. For such a simple model, it is not necessary to do paper template. The blouse pattern shown in this article can be drawn in chalk on the wrong side of your fabric. For the most inexperienced, we suggest paper pattern. To do this, take a sheet thick paper 77x82 cm in size. Transfer our diagram to it, make changes if necessary, and cut out the pattern.

Before cutting, the fabric should be decaged, that is, ironed with a hot iron through a damp cloth. This is done so that the material shrinks and does not decrease in size after you sew a product from it and wash it.

Fold the fabric in half. Connect the top cut to the bottom. Then fold in half again, joining the edges. You should get a square or rectangle with folds on two adjacent sides. Lay the pattern close to the folds and press down on the paperweight so that the fabric and pattern do not move as you trace and cut. The blouse pattern is circled along the contour. Seam allowances are given along the bottom, side cuts and neckline. Neck - 1 cm, side - 1.5 cm, bottom and sleeve hem - 3 cm.

Overlock all cuts, except for the neck. Fold the blouse with the right side inward, align the cuts, baste and stitch in a single line side seams and sleeve seams. Iron them. Turn the hem allowances for the bottom of the sleeves, fronts and backs to the wrong side and baste. Lay the lines, leaving unsewn small areas for threading a narrow linen gum.

The neck must be processed with an oblique inlay so that a drawstring is obtained for pulling the elastic into it. To do this, measure the length of the neck of the blouse, departing 1 cm from the cut. From the remnants of the fabric along the bias thread, cut strips 3 cm wide. Connect them into a ribbon and sew to the neckline, folding them with the right sides. Iron to the wrong side, slightly stretching the unsewn edge. Overcast this edge with a zigzag or overlock. Baste the trim, stepping back 1 cm from the edge. Sew, leaving a small hole for the elastic. If you insert a lace instead of an elastic band and decorate the ties, you can adjust the depth of the cutout according to your desire and mood. A lace or wide ribbon tied in a bow will become a decorative element.

A prerequisite for a good fit on the figure

Patterns of blouses for beginners in no case imply carelessness when sewing. All seams must be treated against fraying. Wet-heat treatment is necessary for each seam. It is not difficult and does not require much time and great experience, but it always affects appearance finished product. Wet heat treatment is the first rule of professionals.

What to look for when buying fabric

And the last recommendation for a beginner dressmaker - when buying fabric, you should pay special attention to the harmony of colors. Even if the fabric is very fashionable and expensive, but the color does not match the skin tone of your face, eyes and hair, then the thing will be "lost" and will not bring the expected joy and satisfaction. The fabric should be selected and with a guideline for your entire wardrobe. Think about how you will wear your new blouse. Suitable for everyday wear or for special occasions. Go through your skirts, trousers, shoes and bags. With such a balanced and thoughtful approach, you will not make mistakes and get great pleasure from the process of creating an outfit, and from the compliments that people will undoubtedly give you.

Among the models of light outerwear in the women's wardrobe, the main place is allocated to the blouse. This piece of clothing is successfully combined with both casual and business attire. Change from strict tones to bright colors, and your look will turn from office to festive. We invite you to create summer blouses with short sleeve with your own hands. They can be sewn or knitted with any tool according to the master classes provided in this article. The simplest patterns of various models will help you quickly cope with the work and replenish your wardrobe with a new thing that will organically fit into any image.

In the past and today

The blouse is a fitted shirt made of lightweight fabric. For the first time this wardrobe item appeared in ancient Greece and was called a tunic. It covered the left side and was fixed on the right shoulder. The Romans had tunics, vaguely reminiscent of a modern blouse. At first they were made by sewing together two panels of fabric, leaving a neck and armholes. Further, the clothes were modernized by sewing a short sleeve.

Even before our era, in Europe, a blouse was used as underwear. The shirt was hidden by a layer of outerwear.

More modern version appeared only at the beginning of the 19th century, when the blouse was no longer worn as underwear. This wardrobe item appeared as a result of the separation women's dress into two parts - a blouse and a skirt. Gradually, the top of the dress began to undergo various metamorphoses, turning into a casual version. Couturiers changed colors and styles, used different fabrics and finishes. This diversity has given rise to huge lineups in the collection of each fashion house. And this is not surprising, because the blouse is considered the most universal thing ladies' wardrobe.

A well-chosen silhouette will easily hide small figure flaws. So, a V-shaped neckline will visually lengthen the figure, and lantern sleeves will divert attention from lush hips. Owners of small breasts can visually increase volumes with the help of ruffles. Take a look at how many looks you can create with a variety of blouses in your wardrobe.

A simple version without a pattern

If you do not own the technique of tailoring, but know how to use sewing machine at the level of a novice user, you can easily create a wonderful summer blouse free cut. You can even not use the machine, but carefully sew the seams by hand. The model is so simple that its tailoring will take from half an hour to 2-3 hours. We propose to make it from a staple with a bright juicy print.

To create clothes, take:

• a staple with a bright print, 1.5 m-60 cm wide;
• sewing accessories - scissors, chalk, thread;
• sewing machine (optional)

The convenience of the model is that there is no waste when sewing. A piece of fabric will completely go to the manufacture of new clothes. To sew a thing, you need a very simple pattern.

Fold the fabric in half and cut into 2 rectangles. It is easy to guess that the sides will be equal to 60 and 75 cm. The sleeves will be short. To create a model with long sleeve fabric, it will take twice as much as the expected length of the product.

Form a shelf from one half of the fabric. To do this, fold the cut in half and lower the center point by 2-4 cm. This value corresponds to the depth of the cut. Measure 14-15 cm horizontally and carefully cut out the "boat".

Cut off the back and front and try on the blouse, check if the head fits freely into the neckline. Make adjustments if necessary. After that, stitch all sections of the fabric with a zigzag.

The bottom of the product can be bent and stitched with a line. Carefully hem the neckline.

Sew the shoulder seams. Here you can show your imagination and complete the seam completely or perform only bartacks along the edges so that the shoulders are open.

To make the blouse sit freely, measure the bust line. Divide the resulting value in half and add 3 cm. Set aside the result on both sides of the center point of the bottom of the product. Seam height (length) - a value equal to the length of the armhole plus a small increase so that the hands freely enter the sleeve.

Sew the details with a zigzag stitch in the places indicated in the photo. Seams are made on front side fabrics.

Elegant summer blouse is ready!

Experiment with fabric, print, cut sizes, and you will get completely different products.

Blouse-transformer

We present you a unique product that is suitable for socks with any bottom.

Another the simplest option updating the wardrobe, the implementation of which does not require special skills and time costs. A cambric blouse with a belt goes well with an elegant skirt. If you remove the accessory, you can create a romantic look by wearing the product with skinny jeans.

You can sew a blouse according to the following pattern.

Fold the cambric in half and cut out the details according to the attached pattern. Perform a stand-up collar with a fastener at the back. Finish the edges of the product and armholes. Sew the center part of the circle to the collar, gathering the piece. Sew a belt, and a romantic blouse is ready.

Knitted blouse-shirt

Summer tops are popular not only among young people, because even quite mature ladies wear such blouses. There are a lot of models of this product, so we suggest that you familiarize yourself with a selection of diagrams with descriptions.

Please note that such a product can be made not only with a crochet. openwork pattern quite easy to form with knitting needles.

Crochet blouse

Things are very popular crocheted. The thinnest openwork emphasize femininity. Blouses made using the technique of ribbon lace look especially good. They consist of lace strips sewn together. Ribbon lace is knitted using a continuous technique, and both experienced and novice needlewomen can make it. Select suitable pattern, connect the openwork strips, and the new thing is ready.

Hello dear needlewomen! There are many different clothes on sale, but many women of fashion prefer to sew blouses and dresses on their own. It will be useful for every woman to know how to sew a blouse with her own hands without a pattern.

How to create a stylish look

To create fashion unique image you need to learn how to sew with your own hands different types clothes. Today we will learn how to quickly sew beautiful blouses of simple styles. By the summer, you can sew a light blouse made of chintz, silk, cambric, chiffon or linen.

For the evening version, it is better to choose chiffon. Chiffon makes airy, light, beautiful wardrobe items. Chiffon is a delicate, sophisticated fabric that requires special treatment. But if you are patient, you will be rewarded with a well-tailored item.

Option for ladies with different complexion.

Helpful Hints for cutting chiffon:

• It is better to cut in one layer, because folded in two layers, chiffon is difficult to keep from shifting.
• First, draw a pattern on paper along with seam allowances, put it on the canvas, press it along the edges with weights.
• Circle with chalk, then carefully cut out. Material cut without distortions is a guarantee of obtaining a beautiful product.
• When cutting chiffon, work on a large table.
• The machine must be set to work with thin material, and the needle must be very sharp and thin.
• Sew the stitch on a piece of fabric first to get the perfect seam.
• To prevent the seams from pulling together, make the stitch length no more than 2 mm.
• Choose the simplest pattern. Complex products can only be sewn by experienced dressmakers.
  It is easier to sew with a lining than without it. If you sew without lining, then the edges can be processed with an inlay from the same material.

Batwing sleeve blouse

Bat back in fashion! In order for a fashionable little thing to appear in the wardrobe, buy 2 points of material, 1.5 meters wide. Measure the circumference of the hips and waist, the length of the sleeve from the neckline to the hem, the circumference of the arm below the elbow.

Stepping through works:

• Fold the material in half "face" inward, then in half again.
• Draw a pattern on the fabric itself. We measure 2.5 cm from the fold down, and 9 cm to the side, this will be the neck.
• From the neck we measure horizontally the length of the sleeve and shoulder. Then from this line for the bevel we measure down 2.5 cm. We draw a line from the edge of the sleeve to the neck.
• We divide the circumference of the waist and hips into 4 parts, set aside along the corresponding lines.
• We connect the bottom of the future product and the edge of the sleeve with a curved line. Cut along the contour.
• The front of the neck is cut a little lower than the back.

We sew the details. To process the neckline, we cut out 2 strips of fabric, each 2.5-3 cm wide. They must repeat the contour of the neckline. Sew to the neck. We bend the bottom of the blouse and sleeves in a zigzag. Sleeves can be finished with cuffs or frills.

Using the following pattern, measure all sizes at once on the fabric. For beginners, it is better to do it on paper.

One of the most simple patterns.

Variant of unusual sleeves.

Quick pattern

A sleeveless pattern model will help to update the wardrobe of both a slender girl and a lady with magnificent forms. It does not require an exact fit to the figure. You only need two parts to get a new piece in your wardrobe, moreover, you can sew it in one evening.

For loose models, choose flowing fabrics so that the products do not hamper movements, hide the flaws of the figure. simple model can be decorated with embroidery or appliqué. Slender ladies can add a thin strap.

Youth option

Blouse for ladies with full arms

Not all ladies can wear sleeveless clothes. To cover up full hands sew a model with a one-piece sleeve. They are suitable for any occasion. Modern young ladies prefer to wear with a floral pattern, as well as in a plain version. Step-by-step tailoring of comfortable products with a one-piece sleeve.

First you need to choose a fabric. The simpler the better. You should not choose bulk material, with an intricate pattern of sequins or embroidery.

Taking measurements:

• chest circumference is measured at the highest points of the chest and shoulder blades;
• the length of the product is measured from the 7th cervical vertebra to the lower edge;
• sleeve length - from the junction of the forearm and shoulder.

Needed for sewing basic pattern which every dressmaker has. When cutting, do not forget to make allowances for freedom of movement at the bottom of the parts, starting from the sleeve - about 10 cm for thin fabrics.

Seam allowances:

• along the neck - 1 cm;
• on the seams - 1.5 cm;
• at the bottom of the product - 4 cm.

The correct shoulder fit can be determined by a blouse that fits you well.

Detail for a perfect fit

This silhouette may have a problem - under the arm the fabric will be very stretched, and the seam allowances in the rounded places will begin to wrinkle ugly. When sewing blouses for overweight ladies, the risk of tearing will increase several times. To soften the tension, sew a gusset in the form of a neat rhombus from the same fabric.

When sewing in, the tops of sharp corners should be directed to the bottom of the blouse and sleeves, and the upper part of the blunt ones should be connected to the corners of the connection between the front and back.

The first fitting is done without a gusset. Make sure that the seams of the sleeves and shoulders do not move from their places.

1. Next, you should grind the side, shoulder, upper and lower sections of the sleeves. Smooth out the seams and overcast.
2. Sew the gusset into the undercut only after sewing and smoothing the seams. Fold the edge of the gusset with the undercut of the front and back inward with the right side.
3. Sew on the rhombus from the side of the blouse so that the seam allowances in the corners are the smallest.
4. Lay out the seam of the gusset on both sides and smooth it with an iron.

Fashion blouse for all ages

The wraparound blouse has won the love of many women. Comfortable and beautiful, it is easy to sew, looks beautiful. The wrap model has a front part consisting of two halves. One half overlaps the other. The smell pleasantly narrows the waist, giving the silhouette a look hourglass. To a simple pattern on the waist line, you can sew two belts, 5 cm wide, then tie them, as shown in the figure.

A flyaway from a square.

Dear fashionistas, by the summer you will have time to sew a few stylish original gizmos to change your wardrobe every day. And each new thing always uplifting!