Openwork stole

Execution technology:

With an auxiliary thread, we perform a set of loops - 192 p. + 1 (for sim.) + 4 (edge) = 197 p. We knit with the main carriage from right to left one row.

Install the p/card in such a way that one row is visible up to the filling level (1).

Brother - with the main carriage we knit one row from left to right, the card is automatically set to the filling level (1 p.). Next, we knit, working with two carriages: with the decker carriage we will move the loops along the pattern (one rapport in height - 6, 4, 6, 4 - carriage movements), putting the carriage into operation on the left side, and with the main carriage we will knit 2 rows of culinary smoothness working on the right.

Silver - replace the main carriage with a decker one, thread the working thread into it and set the density; pattern selection knob - P (smooth surface); side levers - off. (to myself). On the needle bar, we will install constipation-limiters on the two extreme needles of the working area on the left and right so that the loops do not drop. Knit one row in stockinette stitch from left to right. The map is set to the filling level. On the carriage, turn on the side levers (away from you). Next, we knit, switching the pattern selection lever to the second position, while we will remove the thread from the carriage and make the carriage move the loops along the pattern. We return the thread to the carriage and switch the lever to position 1 (cooling the surface) - we knit 2 rows.

We knit a cloth required length(in this case, 566 rubles are knitted), we close the loops without tightening, best with a decker and, at the same time, we do not drop them from the needles, but knit a few more rows with a waste thread after the closed edge.

Remove the canvas, carefully fold in half and sweep, slightly steam through wet gauze, without touching the inflection line. Let it dry a little, then remove the basting, unfold and steam the whole product again.

Take the yarn in 3 cl. and crochet all the edges. You can come up with your own version of the strapping, the main thing is that the edges of the canvas do not wrap too much.

Crochet:

Long sides tied hemstitch from X-shaped columns. Such a hemstitch does not give a large stretch, because. the outer edge is fixed. In addition, we can discreetly carry out a small fit of the web edge.

Short sides tied "fans". If desired, you can cut the yarn folded into skeins into identical pieces and make long brushes. To do this, fold each individual skein in half, thread the loop catcher or hook under the “fan” air loop, grab the skein loop and pull it slightly towards you, then thread the ends into the resulting loop and tighten slightly.

Model Sobova T.V.

Wear it in good health!

In the wardrobe of most women there is a stole. It is both a piece of clothing and an accessory that gives the look a unique look and elegance. Knitted capes have a special chic.
Hand knitting is a long process. Not everyone can afford to devote a lot of time to it. A good helper in this matter is a knitting machine. The stole is knitted on a typewriter quite quickly. Experienced knitters can do it in one sitting. And for beginners, a great opportunity gain experience in machine knitting and master various techniques and patterns.

A beautiful knitted stole is a wonderful gift for a birthday or a holiday. You can quickly impose several different products and give them to relatives and friends, for example, on New Year. Or just urgently solve the problem with a gift.

Another advantage of knitting knitwear on a machine is a perfectly even fabric, even when using very thin threads.

You can knit from yarn of various composition and almost any thickness. It all depends on the class of the knitting machine and what kind of thing is needed - warm and dense to protect against the cold or light openwork to create a complete image of an evening dress. Accordingly, you can knit from wool and wool mixture, cotton, silk, viscose, various mixed and fantasy types of yarn.

The color range of threads has no restrictions. Here, when choosing, only the taste and wishes of the performer or the future owner of the thing play a role.

For knitting a stole on a typewriter, various patterns are used. Most often with openwork weave. Patterns can range from simple nets to intricate ornaments such as Scottish lace.

Plating is a false openwork. It is obtained by using two threads, one of which is very thin - fishing line or nylon. The cape knitted in this way has an exquisite jacquard-like pattern.

From multi-colored threads you can knit a real jacquard. Such products are very bright and original. It is even easier to knit them on the machine with a simple stockinette stitch using section-dyed or melange yarn.

Patterns with a press (fang) weave look interesting. The result is a honeycomb-like fabric. The pattern comes out on the face and inside, and is different, which allows you to wear the thing as you like, twisting and throwing it in different directions.

With the help of knitting "weaving" a weaving pattern resembling a tapestry is imitated. It is produced by applying a finishing thread on the wrong side of the canvas.

You can decorate a stole knitted by a machine with tassels or crocheting. To keep the shape ready product it is necessary to block it - dry it in a stretched fixed form.

This is the simplest of all knitting machines. A beautiful and unusual stole was my first product made on it. It is not difficult at all, you just need to get used to the algorithm of actions.
Before starting work, we fill the machine and analyze the needles: three in the front working position - PNP, seven - in the back non-working position - ZNP. We collect loops using a looper with a pigtail. That is, three loops around the needles, and 7 air loops according to the type of crochet set and again around three needles. We have a report of 10 loops. You can make any number of needles, this will only slightly change the pattern and density of the finished stole.
After a set of loops, we put the thread into the carriage, which should be on the right. We put Russell's levers on both sides in position 1. Thus, we have included partial knitting. With the help of this function, we will knit our beauty.
It looks like this:

We put the last three needles in the middle working position. The rest of the needles remain in the PNP and ZNP, as they were. We knit these three extreme needles with a carriage:

The carriage is on the right. We take the thread and wind it up, as shown in the second photo under the last needle. The thread remains in the carriage. We knit back to the right. We hang the load on the loops of the first trinity. Again we knit these extreme three needles to the left and again we start the thread under the extreme needle.

We do this five times. It turns out here is a picture, before the last sixth time, the carriage is on the right.

We remove the next three needles in the middle working position - PSA. And we knit the first and second trinity.

We start the thread again by the extreme needle.

We put forward the first three needles in the PNP, they are no longer knitted.

We are now working with the second trio. She is in the SRP. We knit 4 times, since the first matches the sixth of the previous three needles. The card is on the right. Again we put the next three needles in the SRP and, moving to the left, we knit the second and third triples of needles. When knitting to the right, we also wrap the outer needle with a thread.

It turns out this canvas:

Having reached the last three needles, we knit them 12 times, not six. That is, we turn in the opposite direction. You get this picture:

Do not forget to change the position of the needles that have already gone out of work on the PNP so that they are not accidentally knitted by the carriage. Change the loads in time, the evenness of the loops depends on them. I recommend knitting this tippet on a gauge of 4 to 6. Knitting too loose will result in a fuzzy pattern. A high density will not allow the product to get airiness.

Finishing knitting is simple - after knitting to the edge, knit six times instead of 12. And close three loops with needles, as usual. Where the needles are in the ZNP, you will have to tinker: dial with a looper air loops and close the trio again on a typewriter.
This stole can be knitted in 4 hours. Since this was my first piece, it took me 8 hours. But having mastered all the operations of pushing the needles, rearranging the loads, counting the knitted rows on the first lower tier, then I knitted almost without looking.
After removing the canvas from the machine, he should be allowed to lie down for a couple of hours. Then wash by hand in shampoo or liquid soap. Press carefully. Drying such a product can only be done on a horizontal surface. Spread your hands on a towel and cover with a second towel on top. If the tippet is too long, fold it in half. Blocking is not needed.
After the masterpiece dries, attach the brushes. To do this, cut the same lengths of thread, and crochet along the edge every two threads in places of the front surface of 3 loops.

Snezhana Novikova

Tippet on the car

You will need: 300 g beige yarn (50% wool, 50% acrylic, 100 g / 1600 m); hook number 1.5.

The front smooth surface, a pattern on a punched card, art. without crochet and art. with a crochet.

Machine test: 32 l, x 42 p. \u003d 10 x 10 cm, the sample is knitted with front stitch on knitting machine Brother 5th grade at a density of 5**.

Attention! The tippet is made on a Brother 5th class knitting machine at a density of 5 **.

Description of knitting a stole on a machine

Pull out 124 needles (62-62) into the PNP and use a loop hook to make a set of “pigtail”. Then work in gauge 5** as follows: 10 rows in stockinette stitch, 216 rows in stt, *18 rows in st, 4 rows in stt (1st to 4th row)*, repeat from * to * 17 more times, 216 rows with a pattern on a punched card, 10 rows with front stitch We knit the last row at a density of 10 **, pull out all the needles in PNP and close the loops with a loop hook “pigtail”.

Assembly:

Steam off the canvas. Crochet wide sides 1 alternately next to st. without a crochet, c. n., and the narrow sides - 1 next to alternately st. double crochet, c. n. On the narrow sides, make tassels 8-9 cm long in finished form.

Tips

Knitted garments should not be hung on coat hangers, as they stretch out under their own weight.

It is better to wash in cool water using special detergents. Soak the knitted product for 3 minutes, wring out several times, but do not rub. Then rinse thoroughly cold water and squeeze lightly.

Do not twist when pressing! Wrap in terry towel and press again. Straighten the product and lay it out on a flat surface, preferably on a fabric that is well breathable.

In order to clearly track the rows when knitting, we advise every 10 p. mark the extreme loops. This will greatly facilitate your further calculation.

Knitting a top on a machine

The size 46-48

You will need: 200 g of blue yarn (50% wool. 50% acrylic, 100 g / 800 m); hook number 1.5.

Facial surface, art. without a crochet.

Main pattern:

1st row * 9 p. persons. stitch, slide the 10th needle into the NP, and hang the 10th loop on the 11th p. *, from * to *, repeat to the end of the row;

2-6th row: front surface (every 10th needle is also in NP);

7-18th row: front surface (on all needles);

19th row: * 14 p. persons. stitch, slide the 15th needle into the NP, and hang the 15th loop on the 16th p. *, from * to *, repeat to the end of the row;

20-25th row: front surface (every 10th needle is also in NP);

26-37th row: front surface (on all needles). Alternate from the 1st to the 37th row.

Pico: 1 tbsp. single crochet, 3 in. p. and conn. Art. in Art. without a crochet. from which they began to knit in. P.

Machine test: 34 p. x 46 p. \u003d 10 x 10 cm, knitted with the front stitch on a Brother knitting machine of the 5th grade at a density of 4 *.

Attention! The top is made on a Brother knitting machine of the 5th class at a density of 4 *.

Back:

Pull out 166 needles (83-83) into the PNP and, by entwining, dial the first row, for a hem, knit with front stitch 6 rows at a density of 3.2 rows at a density of 2**, 2 rows at a density of 2*, then in reverse order. After knitting 20 rows on the counter, reset it, put the loops of the first row on the working needles and knit together with the working loops with the front stitch at a density of 4 *. Next, knit with the main pattern. Having knitted 290 rows according to the counter, for shoulder bevels close on both sides in each 2nd row 6 times 5 p. And 4 times 4 p. 2 times 10 p., 2 times 5 p., 1 time 4 p. and 1 time 3 p. Finish the work.

Before:

Knit to the armholes, like a back, Having knitted 184 rows along the counter, to expand the fabric, add on both sides in each 7th row 15 times 1 p. After knitting 290 rows along the counter, for shoulder bevels, close on both sides in each 2nd row 6 times for 5 p. and 4 times for 4 p. 1 row on all loops and cast off.

Assembly:

Steam the details. Perform shoulder and side seams. Crochet armholes and neckline: 1 row alternately 3 tbsp. single crochet, pico.

Hat MK Chasika

On the account of MK hats: yes MK Chasik, my head girth is 52 cm, I had a set of 70-0-70 wrong side on pl6 ** 72 rows, then an eyelet.
Kink: 4p pl6 **; 2r square 9; 4r square 6**; connecting row square 10
The outer part of the jacquard immediately after the fold and eyelet on PL 8.
Outer only 66r of the pattern, double decrease, 2p smooth, double decrease, a row of smooth and tighten with a thread. I pulled it together with a thread, adding a thick synthetic thread, the angora is not very strong for tearing.
My layout: the back of the head is 12 loops. forehead 10-0-17 the rest for tying the ears.
Do not rely heavily on my numbers, just as a guideline - do your calculations!, I bandaged the hat 2 times (the first time it turned out great, tried it on my head and already tied it with the adjustment for the second time).

girls, the promised description of a children's hat with ears and a placket across the face. I'm sorry that it was later than the promised time, but the children were so sick that I even "got along" with the pharmacists in the pharmacy.
The whole hat is knitted on one fonture, so many people can knit it. I will describe how I knitted a hat for my daughter and a photo of her.
And so let's get started. Let's start with some calculations. My loop test 3.5 * 5r. It is necessary to measure the child's forehead. I measure from one end of the eyebrow to the end of the next. In my case it is 11.5 cm. I know that many consider ears, how to divide all the number of loops into five, of which 2 parts are the forehead, one part is the back and one part is the ears. I don't like how awkward it sits. Therefore, I think so. Double hat, yarn 32/2 in 4 ends
We collect 140 loops with waste thread, we knit several rows and one row with a cord cord.
I have a carriage on the left after a row with a cord. Threading the working thread Pink colour and knit 70 rows. We turn off the counter and forget about it for a while. I adapted like this to make money from junk and combs.

The carriage is on the left, the levers are on the CV, we put forward the needles 20-0-70 in the PNP. Remember I told you to measure your forehead. I have it 11.5 cm, i.e. central 40 needles (20-0-20).

We knit a row, wrap the last needle with a working thread so that there are no holes and push the 10 needles on the left into the PNP. It is enough for the back for children up to 5-6 years old.

And so we knit by pushing one needle from the opposite side of the carriage into the PNP, not forgetting to wrap the thread around and outweigh the weights. So we knit until 10-12 needles remain in the work, less is needed, the ear will not be beautiful. I have 11 needles left. The carriage is on the right, we push the needles on the extreme left a little so that they are knitted and we knit a row. At the same time, remember the last needle on the far right in the PNP. I have this 35th needle. Let's just remember everything.

So, we tied one part of the inner one of the ear. break the thread and remove these needles from work. We transfer the carriage to the right side and knit the inner part of the second ear in the same way. Having finished knitting it, the carriage will be on the right. We turn off the CV levers and change the thread to lilac. I advise you to knit the first such hat different color to understand how the plank fits. Then you will spit with eyes closed and one color. We knit at working density 8 rows, 2 rows are looser by 2 units and 8 more rows at working density. I have a working density of 5, 2 loose rows at 7 density, this is the place where the bar is bent.

Now we remove all the loads, take out the comb, slightly push the needles, but so that the loops do not run behind the tongues, otherwise it will be difficult to hang the bar. We take a decker and hang a bar for the very first lilac loops. The first time I did it for a very long time and then I decided that I would not knit like that anymore. In general, since the beginning of the month I have knitted 9 such hats.

when everything is done, we put forward all the needles in the PNP, so it is easier for the machine to knit and we knit one row 2 units looser. Plank at work, you can’t see it, but you can already touch it

The carriage is on the right, we turn on the CV levers, we put forward needles 35-0-70 into the PNP. Remember, we memorized a needle? Here we put the needles up to it. We knit a row, from the 35th needle we count 11 needles. These are the needles that we had left in work when we knitted our ear. And we put forward the needles on the far right into the PNP

We knit a row, the carriage is on the right, the first needle opposite the carriage in the PNP is slightly pushed with a finger so that it is knitted in the future. Knit a row and do the same on the other side. There is no need to wrap thread. Don't forget to hang weights.

So we knit until the needle returns to work up to 20 needles, this is our forehead, remember? In this case, the carriage must be on the right. And on the left, we push the last 10 needles so that they knit. You should be like this

So our ear is knitted, the carriage is on your left. We bring these needles of the connected ear into the PNP, break the thread and move the carriage to the right side. We knit the second ear in the same way. When finished with it, your carriage will remain on the right. We turn off the CV levers, turn on the counter and knit 70 rows, it can be jacquard, it can be stripes or just plain. As you wish.

When our rows are connected, we again take the decker in our hands and hang our very first loops on the needles. A little more and we will remove our beauty from the car. We pull out the cord cord, remove the throw, and knit 6 more rows, then we hang the loops through one and knit 4 more rows. I knit the very last row on the loosest density, this is 10 *. We cut the thread, leaving it for stitching, knit a few rows with a throw and cut it off the machine